Perancangan Sistem Otomasi Level Pada Plant Alat Uji Kebocoran Pipa Sebagai Penunjang Praktikum Sistem Instrumentasi Industri

Zazimah, Siti (2018) Perancangan Sistem Otomasi Level Pada Plant Alat Uji Kebocoran Pipa Sebagai Penunjang Praktikum Sistem Instrumentasi Industri. Diploma thesis, Institut Teknologi Sepuluh Nopember.

[thumbnail of 10511500000068-Non_Degree.pdf]
Preview
Text
10511500000068-Non_Degree.pdf - Accepted Version

Download (1MB) | Preview

Abstract

Aliran bertekanan di dalam pipa menuntut kekuatan pipa PVC yang memadai. Kekuatan pipa PVC perlu diuji untuk mengetahui kuat tekan dari aliran dalam pipa. Dimana kebanyakan alat penguji berbentuk mesin press hidraulik untuk mengetahui kekuatan pipa tersebut. Adapula alat uji kebocoran pipa yang dihasilkan dari suatu aliran fluida yang bertekanan. Untuk membuat alat uji kebocoran pipa dari suatu aliran fluida yang bertekanan dibutuhkan suatu sistem otomasi level untuk mengisi dan mengosongkan tangki pada ketinggian 35cm hingga mencapai tekanan yang diinginkan. Dimana tekanan yang dihasilkan dari level air bertujuan untuk menambah tekanan yang dihasilkan oleh air di dalam tangki. Dengan adanya sistem otomasi level ini maka selain ketinggian air dapat diotomatiskan juga dapat menambah tekanan sehingga dapat membantu kinerja dari kompresor agar lebih cepat dalam menambah tekanan yang digunakan untuk menguji pipa. Air yang dipompa menuju ke tangki kemudian dideteksi oleh sensor float level switch. Ketika sensor sudah mendeteksi air sampai mencapai ketinggian 35cm maka solenoid valve akan menutup. Hasil pengujian yang didapatkan yaitu aktuator membuka 100% ketika dalam keadaan low dan akan membuka 0% ketika high. Waktu yang dibutuhkan untuk mencapai set point adalah 66 detik.
==================================================================================================
The pressurized flow within the pipe requires adequate PVC pipe strength. The strength of the PVC pipe needs to be tested to determine the compressive strength of the flow in the pipe. Where most of the tester shaped hydraulic press machine to know the strength of the pipe. There is also a pipe leak testing apparatus produced from a pressurized fluid stream. To make a pipe leak testing apparatus of a pressurized fluid stream requires a level automation system to charge and discharge the tank at a height of 35cm until it reaches the desired pressure. Where the pressure generated from the water level aims to increase the pressure generated by water in the tank. With the existence of this level of automation system in addition to the height of the water can be automated also can increase the pressure so it can help the performance of the compressor to more quickly in adding pressure used to test the pipe. The water pumped into the tank is then detected by the float level switch sensor. When the sensor has detected water until it reaches height 35cm then solenoid valve will close. Test results obtained that actuators open 100% when in a low state and will open 0% when high. The time required to reach the set point is 66 seconds.

Item Type: Thesis (Diploma)
Uncontrolled Keywords: Mesin Press Hidraulik, Uji Kebocoran Pipa, Sistem Otomasi Level, Set Point, Float Level Switch. Hydraulic Press Machine, Pipeline Leakage Test, Level Automation System, Set Point, Float Level Switch.
Subjects: T Technology > TC Hydraulic engineering. Ocean engineering > TC424 Water levels
Divisions: Faculty of Vocational > Instrumentation Engineering
Depositing User: Siti Zazimah
Date Deposited: 04 Aug 2021 23:53
Last Modified: 04 Aug 2021 23:53
URI: http://repository.its.ac.id/id/eprint/58333

Actions (login required)

View Item View Item