Perancangan Sistem Hidrolik Blank Holder Pada Proses Deep Drawing Untuk Pembuatan Cup Selongsong Peluru Kaliber 20 mm

Giri, Yoga Yama (2015) Perancangan Sistem Hidrolik Blank Holder Pada Proses Deep Drawing Untuk Pembuatan Cup Selongsong Peluru Kaliber 20 mm. Undergraduate thesis, Institut Teknologi Sepuluh Nopember.

[thumbnail of 2109100071-Undergraduate_Thesis.pdf]
Preview
Text
2109100071-Undergraduate_Thesis.pdf - Accepted Version

Download (4MB) | Preview

Abstract

Dalam pembuatan selongsong peluru, proses sheet metal
forming berupa deep drawing dan ironing dilakukan. Pada proses
deep drawing, terdapat komponen blank holder yang berguna
untuk menjepit benda kerja. Pada proses deep drawing
konvensional, mesin press digerakkan secara mekanik dengan
roda gila, blank holder dan drawing ram digerakkan oleh satu
poros utama. Hasil yang didapatkan dari proses konvensional ini
adalah gaya dan kecepatan blank holder yang tidak mampu
dikontrol dengan baik, sehingga bisa mengakibatkan kecacatan
pada produk seperti wrinkle, tearing dan crack. Selongsong peluru
yang cacat mengakibatkan peluru tidak dapat ditembakkan dengan
maksimal.
Berdasarkan dari permasalahan di atas, suatu mekanisme
untuk mengatur gerakan pada blank holder diperlukan, yaitu
sebuah sistem hidrolik. Langkah-langkah penelitian yang
dilakukan meliputi perancangan proses pembuatan cup dari
sebuah blank, kemudian dilanjutkan dengan perancangan blank
holder pada proses deep drawing. Langkah selanjutnya adalah
perancangan sistem hidrolik untuk menggerakkan blank holder,
setelah itu dilakukan simulasi dengan menggunakan software
FLUIDSIM.
Dalam perancangan sistem hidrolik blank holder pada
proses deep drawing untuk pembuatan cup selongsong peluru
iv
kaliber 20 mm, posisi blank holder set terletak di bawah benda
kerja. Blank holder berbentuk persegi empat sama sisi dengan
dimensi 100 x 100 mm dan tebal 30 mm. Pada blank holder,
terdapat lubang dengan diameter 74 mm sedalam 5 mm sebagai
tempat meletakkan blank dan terdapat lubang untuk punch dengan
diameter 42 mm. Pin berjumlah 4 buah dan berbentuk silinder
dengan diameter 25,4 mm dan tinggi 120 mm, sedangkan plat
bawah berbentuk persegi empat sama sisi dengan dimensi 100 x
100 mm dan tebal 30 mm. Pressure relief valve di setting sebesar
13 bar dan screw atau knob pada flow control valve di putar 3,75
kali (CCW) dari kondisi fully closed, sehingga pada saat silinder
retract memberikan gaya holding ke atas sebesar 10,2 kN, dan
silinder turun dengan kecepatan 0,03 m/s. Pressure pada power
pack di setting 17,37 bar dengan flow rate 15,54 liter/min,
sehingga mampu menggerakkan silinder saat naik dengan
kecepatan 0,03 m/s.
==================================================================================================
In order to make shell casings, sheet metal forming process
like deep drawing and ironing must be done. In deep drawing
process, there is a component named blank holder that useful to
clamp the workpiece. In the conventional deep drawing process,
press machine are driven by mechanical with a flywheel, blank
holder and drawing ram are driven by one main shaft. Result of
this conventional process is force and velocity of blank holder can
not be well controlled, so that will result defection in the products
such as wrinkle, tearing and crack.. Defection in shell casings,
make the bullet can not be fired well.
Based on the problem above, it needs a mechanism that
can control the movement of blank holder. It is a hydraulic system
that can control the movement of the blank holder. The step in this
research, includes design the process making cup from a blank,
then continued with design blank holder in deep drawing process.
The next step is to designing hydraulic system to make blank holder
move, after that simulation is performed by using fluidsim
software.
In designing hydraulic system of blank holder in the deep
drawing process for making shell casing cup caliber 20 mm,
position of the blank holder set is located under workpiece. Blank
holder has square form (100 x 100 mm) with 30 mm height. At
blank holder, there is a hole in the center (ø 74 mm) with the depth
of 5 mm for a place to put blank and there is another hole for the
vi
place of punch (ø42 mm). The number of pins used by 4 units and
have cylindrical shape (ø 25,4 mm) with 120 mm height, while plate
has square form (100 x 100 mm) with 30 mm height. Pressure relief
valve must be setting 13 bar and screw or knob at flow control
valve is rotated 3,75 times (ccw) from the fully closed condition in
order to give force to the top by 10222,32 n and cylinder moving
down with velocity 0,03 m/s. Pressure in power pack must be
setting 17,37 bar with flow rate 15,54 liter/min in order to make
cylinder moving up with velocity 0,03 m/s.

Item Type: Thesis (Undergraduate)
Additional Information: RSM 671.253 Gir p
Uncontrolled Keywords: Deep drawing, blank holder, sistem hidrolik
Subjects: T Technology > TJ Mechanical engineering and machinery
Depositing User: Yeni Anita Gonti
Date Deposited: 28 Feb 2020 03:18
Last Modified: 28 Feb 2020 03:18
URI: http://repository.its.ac.id/id/eprint/75226

Actions (login required)

View Item View Item